Quick Notes:
The same engineering that made RPM Rod Ends for Associated and Losi vehicles some our best selling RPM parts for over 2 decades has gone into the creation of RPM Rod Ends for Traxxas 1/10th scale vehicles. These rod ends are tough! The area around the ball stud is thicker than the stock rod end while still allowing a full range of motion of the pivot ball. Additionally, the shank has been redesigned with a pair of flats, making the rod end much easier to work with (versus the stock, round shank). RPM rod ends are sold in sets of twelve to complete most vehicle needs.
RPM Rod Ends cover a wide range of currently available Traxxas vehicles including all versions of the following: Slash 2wd, Slash 4×4, Summit, T-Maxx, E-Maxx, Revo, e-Revo, Slayer Pro 4×4, Stampede 4×4, Rustler 4×4, Rustler VXL, Jato and Bandit VXL.
Tech Notes: RPM long rod ends replace Traxxas stock #5525. Sold without pivot balls. Stock Traxxas pivot balls are required for completion.
Varenr TRX 5525
These are the Rod Ends and Balls for the Traxxas Slash 4x4 and other Traxxas cars. FEATURES: Black nylon...
Gear, 20-T pinion (32-p), heavy duty (machined, hardened steel)/ set screw For some drivers, “heavy...
Driveshaft assembly, rear, extreme heavy duty (1) (left or right) (fully assembled, ready to install)/ screw pin (1)
Tires & wheels, assembled, glued (2.8") (RXT black wheels, Talon Extreme tires, foam inserts) (2) (TSM rated)
This is the Complete Slipper Clutch Set for the Slash 4X4 and Stampede 4x4 from Traxxas. FEATURES: Complete...
Nerf Bars for the Traxxas 1/10th scale Rally & LCG Slash 4×4 Quick Notes: – replaces stock...
This is the Heavy Duty Driveshaft Assembly for the Slash 4x4 from Traxxas FEATURES: Black plastic and steel...
Rebuild kit, steel constant velocity driveshaft (includes drive pin & cross pin for two driveshaft assemblies)
This is the optional Clear Gear Cover for use on the Traxxas Slash 4x4. FEATURES: Plastic construction...
Smart™ Technology Overview LiPo batteries with Spektrum Smart™ technology practically take...
Driveshaft, center rear, 6061-T6 aluminum (black-anodized) (fully assembled)/ 3mm screw pin (2)
Gear, 27-T pinion (0.8 metric pitch, compatible with 32-pitch) (fits 5mm shaft)/ set screw
Gear, 31-T pinion (0.8 metric pitch, compatible with 32-pitch) (fits 5mm shaft)/ set screw
Denne passer fint på AXIAL SCX10 This is the Pro-Line Baja Bug Body for use on the Traxxas Slash....
Body, Slash 4X4, heavy duty (clear, untrimmed, requires painting)/ window masks/ decal sheet
This is a set of two replacement rear hub carriers from Traxxas. These hub carriers mount to the rear lower control...
RPM Rear Bearing Carriers for Hoss 4x4, Slash 4×4, Rustler 4×4, Telluride, Nitro Slash & Stampede...
Differential output yoke assembly, extreme heavy duty (2) (left or right, front or rear) (assembled with...
RPM Rear Bumper for Slash 4×4 - Blue Replaces stock Traxxas #6836 Quick Notes: Replaces stock Traxxas...
RPM Low Visibility Wheelie Bars for Slash 2WD, Slash 4×4, Losi SCTE & ECX Torment 4×4 Quick Notes:...
This is the Traxxas 7-Cell 8.4V 3000mAh Power Cell NiMH Hump Pack with iD Connector. ...
